Takayama DT Flex Fin: The Longboard Single Fin That Pivots and Holds

Pivot when you want. Hold when you need it.
Takayama DT Flex Fin

A handmade longboard single fin with an upright base for tight turns and a raked tip for hold on the nose.

Shop the DT Flex Fin
Takayama DT Flex Fin longboard single fin, side view showing the upright base and raked tipLongboard fin box showing the Takayama DT Flex Fin with the plate and screw at the back of the box
✓ Honolulu surf shop since 1996 ✓ Handmade in California ✓ Sizes for mid-lengths to logs

Quick answer: The Takayama DT Flex Fin is a longboard single fin that does two jobs. The bottom two thirds follow a pivot template for tight turns, and the top third rakes back, or sweeps toward the tail, for hold when you walk to the nose and in drawn out turns.

It suits intermediate longboarders who want one single fin for nose rides and turns, and it helps a surfer moving up from beginner feel steadier up front. Sizes run from about 8" for mid-lengths to 10.5" for big logs.

What Is the DT Flex Fin?

The DT Flex Fin is a Donald Takayama single fin template with a pivot base and a raked tip. A pivot fin is upright with a wide base, so the board swings around in a tight arc. A raked fin sweeps back, which adds hold and drive.

The Flex Fin puts both in one fin. The wide base gives you something solid to push against, the middle moves between push and release, and the raked top holds the board steady when you are up front.

The template started as a fin for single fin eggs and mid-lengths before Donald scaled it up for longboards.

Who Is the DT Flex Fin For?

It is built first for intermediate longboarders who want one single fin for nose rides and turns.

Intermediate longboarders. You want to turn tight in a closing section and still have hold on the nose. The Flex Fin lets you do both without changing fins.

Surfers moving up from beginner. As you start walking forward, the raked tip helps the board feel steadier and slows it down a little, so nose rides feel more controlled.

Riders of wider tail longboards. A wide tail can feel hard to control as the waves get bigger. The extra hold helps keep it in check.

Mid-length and egg riders. An 8" or 8.5" Flex Fin works well in a single fin egg or mid-length.

How Does the DT Flex Fin Surf?

On the nose, it holds. When you walk forward, the raked tip slows the release of water off the fin, which keeps the board steady. On a flat rocker board that wants to run fast, it helps you control that speed.

In turns, it pivots or draws out. The pivot base lets you swing the board around in a tight section, and the rake lets you hold a long, drawn out turn when the wave opens up.

It feels a little shorter than it measures. Because of its flex and rake, a 9.5" Flex Fin feels closer to a 9" standard fin, so you can run a bit more fin for hold without the board feeling stiff.

Why Does It Suit Hawaii Waves?

Hawaii waves often come in sections rather than one long, even wall. You ride across, make a section, get on the nose, then turn to make the next one.

A pure pivot fin can feel too loose for the power turns, and a heavily raked fin can feel too stiff for quick changes. The Flex Fin sits between them, which fits the way waves break on Oahu's South Shore.

What Size DT Flex Fin Should I Get?

Match the fin to your board length, then adjust for tail width and weight.

Takayama DT Flex Fin starting sizes
Board length Fin size Good for
7'6" to 8'6" 8" to 8.5" Single fin eggs and mid-lengths
9'0" and under 9" to 9.5" Standard longboards
9'0" to 9'6" 9.5" to 10" A common longboard setup
9'6" and up 10" to 10.5" Bigger logs and noseriders

If your tail is narrow, under about 14.5", you can size down a little. A wide tail, 15" or more, usually does better at the larger end. Heavier surfers should also lean toward the larger end.

More on sizing is in our longboard fin size guide.

Where Does It Go in the Fin Box?

Start in the middle of the box, then move it. Forward makes the board looser and more pivoty. Back gives more hold and drive in your turns.

Put the plate and screw at the back of the fin, not the front. The rake puts a lot of load on the back edge as the fin flexes. Hardware at the back supports that load and helps prevent the fin tab from cracking.

How Is the DT Flex Fin Made?

Each Flex Fin is handmade in California by Larry Allison, who has made Donald Takayama's fin templates since the mid 1990s.

Every fin is laid up from 29 layers of 7.5 ounce cloth, two layers at a time, then foiled by hand. The heavier cloth lets the fin keep a strong spine, its thickest point, about a quarter of the way back from the front edge.

That spine and foil give the fin twist and spring as it flexes, instead of just bending side to side. There is also a Hawaiian fabric inlay edition.

Who Was Donald Takayama?

Donald Takayama (1943 to 2012) grew up surfing in Waikiki and founded Hawaiian Pro Designs. He shaped boards and fins for more than five decades.

His other fin design is the Halo fin system, a center fin and side bite set. Read more in Who Was Donald Takayama?.

Ready to Pick Your Flex Fin?

Tell us your board length, tail width, weight and how you like to surf, and we will help you pick a size and set it up. Come by the shop to see the fins in person.

Shop the Takayama DT Flex Fin

Hawaiian South Shore
320 Ward Ave, Suite #111, Honolulu, HI 96814
Call or text (808) 597-9055
sales@hawaiiansouthshore.com

Frequently Asked Questions

How is the Flex Fin different from a standard pivot fin?

Both have an upright base for pivoting, but the Flex Fin's top third rakes back. That adds the hold and drive of a raked fin for nose rides and drawn out turns.

Is the Flex Fin good for nose riding?

Yes. The raked tip holds the board steady when you walk forward, and it helps slow down a flat rocker board that wants to run too fast.

What size Flex Fin should I get?

Start by matching fin size to board length, so a 9' board gets about a 9" fin. Go larger for a wide tail or if you are heavier. It feels about half an inch shorter than it measures.

Why should the screw plate go at the back of the fin box?

The rake puts load on the back edge as the fin flexes. Hardware at the back supports it and helps prevent the fin tab from cracking.

Can I use the Flex Fin on an egg or mid-length?

Yes. The template started as a mid-length fin, and an 8" or 8.5" Flex Fin works well on single fin eggs and mid-lengths.

Who makes the Takayama DT Flex Fin?

Larry Allison makes each one by hand in California, from 29 layers of 7.5 ounce cloth, and he has made Donald Takayama's fin templates since the mid 1990s.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.